search

KUHN RIKON Corp. Drill 30-100 Manuel d'utilisateur Page 3

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 24
  • Table des matières
  • DEPANNAGE
    •
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 2
SAVE THESE INSTRUCTIONS.
Refer to them often.
3
California Proposition 65 Warning
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Your risk from
exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in
a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to lter out
microscopic particles.
For more detailed information about California Propostion 65 log onto rikontools.com.
ALWAYS CHECK FOR DAMAGED PARTS.
Before initial or continual use of the tool, a guard or other part that is damaged should be checked to
assure that it will operate properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its
operation. A guard or other damaged parts should immediately be properly repaired or replaced.
ALWAYS DISCONNECT TOOLS.
Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.
ALWAYS AVOID ACCIDENTAL STARTING.
Make sure switch is in “OFF” position before plugging in cord.
NEVER LEAVE TOOLS RUNNING UNATTENDED.
Special Safety Rules For Drill Presses
1. Do Not operate the Drill Press until it is assembled
and you have read the instructions.
2. Do not operate the Drill Press unless you are familiar
with its safe operation. If you are not familiar with
the operation of a Drill Press seek advice from your
supervisor, instructor or other qualied individual.
3. If you are using a bench top Drill Press, it must be
securely fastened to a stand or bench.
4. If you are operating a oor Drill Press it must be
securely fastened to the oor.
5. Always clear the table and work area before turning
on the Drill Press.
6. Always use drill bits, cutting tools and accessories
with a ½” shank or less.
7. Never place hands near the drill bit, cutting tool or
accessory.
8. Never wear loose clothing, gloves or ties while
operating the Drill Press.
9. Always have a rm footing while operating the Drill
Press.
10. Always keep work surface and work areas clear of
debris.
11. Never attempt to do set-up work, assembly or layout
work on the Drill Press while it is in operation.
12. Never start the Drill Press with the drill bit, cutting
tool or accessory in contact with the work-piece.
13. Always lock all table, column and head locks before
turning on the Drill Press.
14. Never operate the Drill Press with a damaged drill
bit, cutting tool or accessory.
15. Always check the drill bit, cutting tool or accessory
in tight in the chuck.
16. Never operate the Drill Press with the chuck key
in the chuck.
17. Always adjust the depth stop to avoid drilling into
the table surface.
18. Never drill material unless it is properly supported.
Non at work-pieces require additional support.
19. Always clamp the work piece to the table.
20. Always support large work-pieces at the same
height as the table.
21. Never remove the work-piece or clear the table
until the Drill Press comes to a complete stop.
22. Always wear a face shield and safety glasses while
operating the Drill Press.
23. Never operate the Drill Press with missing,
damaged, worn, loose or defective parts.
24. Never adjust, change speeds or perform
maintenance on the Drill Press while it is operating.
25. Always clean the work surface and work area when
nished operating the Drill Press.
26. Always disconnect the power when adjusting or
performing maintenance on the Drill Press.
27. Always disconnect the power when nished using
the Drill Press to prevent accidental operation.
Vue de la page 2
1 2 3 4 5 6 7 8 ... 23 24

Commentaires sur ces manuels

Pas de commentaire
  • Acroprint ATHENA POWER Clickfree Sierra-monitor-company Salsbury Industries
  • Oregon Scientific Horloges murales EMachines Non Pioneer Mesure, test et contrôle 3com Téléphones IP Mustang Survival Non
  • Graco 3000 LG UM3C Electrolux EHF6343FOK Ableton Live - 5.0 Electrolux EWW51676SWD
  • Uniden DECT2080 Manuel de l'utilisateur Taylor 1488 Manuel de l'utilisateur AvMap EKP III C Manuel de l'utilisateur Remington Wet 2 Spécifications Altronix eFlow6N Guide d'installation